DodgeTalk Forum banner
Status
Not open for further replies.
1 - 16 of 16 Posts

· You've been Hijacked
Joined
·
15,407 Posts
Discussion Starter · #1 ·
For the power wire with a hemi, do you have to take the stock hemi hat off to get to the plug for the power wire? I found what I think is the right plug, but I can't even get my hand in there properly and I don't want to just start pulling on wires.

Also If anybody has a good pic of it installed so I can see where the plug is that would also be appreciated.
 

· Registered
Joined
·
2,639 Posts
Quietpeen, your IAT sensor is plugged into the hemi hat on the front side right where the tube comes from the air filter. Right under the "H" and the 5.7
 

· You've been Hijacked
Joined
·
15,407 Posts
Discussion Starter · #5 ·
danimalhemi24 said:
you don't need to pull the hemi hat off. I did come with instructions didn't it?
i bought it used off of KRS, but got the intructions sheet from another thread.

duso02 said:
Quietpeen, your IAT sensor is plugged into the hemi hat on the front side right where the tube comes from the air filter. Right under the "H" and the 5.7
thats where I thought it was but i can't get my hand in there to pull on the plug. Does it slide right off or is there clip like all the other plastic plugs on vehicles?
 

· Registered
Joined
·
2,639 Posts
If I remember correctly, it's a keyway deal. A 1/4 turn in one direction should free it up.
 

· (_)& (_)& (_)&
Joined
·
507 Posts
it clips, i had to take the pcv tube off to fit my hand there
 

· Registered
Joined
·
247 Posts
Shouldn't have to move anything...I did mine in about 5 minutes on my lunch break
 

· Registered
Joined
·
2,639 Posts
williboone said:
it clips, i had to take the pcv tube off to fit my hand there
Good point...let me clarify: the connector is a clip but I was talking about pulling the whole IAT so I could see it.
 

· You've been Hijacked
Joined
·
15,407 Posts
Discussion Starter · #10 ·
duso02 said:
Good point...let me clarify: the connector is a clip but I was talking about pulling the whole IAT so I could see it.
that sounds like my best option. That way I won't have to worry as much about break the clip. Maybe I will go out during my lunch and try that(who am I kidding....I will be out there around 10:30 :D )
 

· 25HEMI00
Joined
·
1,063 Posts
just be really careful not to break the sensor. You will feel the 1/4 turn. If i'm not mistaken it's gonna be counterclockwise. Don't forget to reset your pcm for the new A/F mix.
 

· You've been Hijacked
Joined
·
15,407 Posts
Discussion Starter · #12 ·
25HEMI00 said:
just be really careful not to break the sensor. You will feel the 1/4 turn. If i'm not mistaken it's gonna be counterclockwise. Don't forget to reset your pcm for the new A/F mix.
I thought I read to you don't have to reset the pcm with the powerwire
 

· 25HEMI00
Joined
·
1,063 Posts
me 2. i just did.
 

· You've been Hijacked
Joined
·
15,407 Posts
Discussion Starter · #14 ·
thanks for the help guys. I was able to find the right location and get it installed.
 

· Master Baiter
Joined
·
582 Posts
quietpeen said:
I thought I read to you don't have to reset the pcm with the powerwire
You don't have to, but it helps to get a fresh start. It'll "learn" quicker.
 

· Registered
Joined
·
255 Posts
Stand on the front bumper to get at it at a better angle and it will come right off. I
had the same problem.
 
1 - 16 of 16 Posts
Status
Not open for further replies.
Top