Search Results for ‘pcm’

Hey everyone. I have a question about an engine swap. Currently I have a 2008 Dodge Ram 1500 4x4 quad cab with the 5.7L HEMI. It is my daily driver and runs pretty well aside from exhaust manifold leaks and it feels a little underpowered, especially when towing. For example, I only get 8 mpg...

This will be a long and involved post, but I hope someone knowledgeable about these things can help me out! I've owned my 1999 Dodge 3500 Van since new. It's had some major rust problems in the front end, due to being driven in Midwest winters. I had the front end replaced this summer, which...

Just bought a 1998 Dodge Ram 1500 4wd for pretty cheap. Got it as a project. Last owner hit a bump and truck cut off and won't start back up. Read about PCM issues in other forums and wanted any advice on where to start with trying to find problem so I can actually drive the truck. Thanks.

My '97 Dakota 3.9 is not starting, and I'm pretty sure it's the PCM. (For a short time, jiggling one of the wires at the PCM allowed it to start/run, but it's not working anymore.) I'm getting ready to order a new one, and there are good and bad reviews for just about every place I could go...

I purchased a refurbished PCM for my 2005 Ram 1500 5.7L HEMI and went to replace out the old one. For some reason, the previous owner of the truck glued in the connectors for two of the plugs and after prying off the plugs, the color-coded pin protectors broke off and are still glued into the...

long story short, found my stock jtech pcm is going bad. Had crank no start. Found I have to turn key on, leave it in on position in order to “warm up the pcm”, then proceed to crank it over. Now my question is, my engine is built (heads, cam, bored 20^, headers) and I already had the stock pcm...

I am helping my aunt with her 98 Stratus V6. It may need a PCM. I would like to know which year PCMs and which part numbers will work. I read about some cars coming equipped with anti theft systems that complicates this issue. I do not know if this car has any security system like SKIM. It does...

Getting a P0443 code on a 1998 Ram 1500. The is a "circuit" problem. Evap purge solenoid is new. Even so it is closed when removed from the system and when I apply voltage and ground I can feel and hear it open. So I don't think the problem is here. With the key on/engine off: At the...

I have a late 2002 Durango 4.7 with the 4 plug NGC computer. I would love to be able to use HPTuners on it and have more tuning ability. HPTuners only supports NGC3 computers though, which didn't come out until 04. Mine is an NGC1. Would it be possible to swap to an NGC3? If so, what would be...

I'm looking for some confirmation that I need to change my PCM due to it throwing P0443 code immediately even after clearing codes. This is a 2003 Dodge Ram 1500 Hemi with 160,000 miles. I've searched all the threads on this code and have done the following. Replaced Fuel Cap. vacuum tested all...

Okay guys, here's the full run down... During the beginning of the trucks life it would occasionally die while making turns, maybe once every 4 months or so, always started right back. About two years down the road it sputtered out and died on the highway, started right back up with the check...

Hi, thanks for reading. I've searched, but can't post links yet :nerd Once I can post links I'll update OP ==> I'm curious if there's an answer since 2012 that avoids having to use a dealer to flash PCM CLOSEST POST: P0344 P0340 codes, mentions PCM needing a flash & the specific TSB...

I have a Dodge Grand Caravan SE 3.3L Flex Fuel van, that keeps turning on my Check Engine Light (MIL) after I drive it for about 10-20 minutes every time. I have replaced both of the O2 sensors with factory OEM replacements and this has not changed the condition at all. I checked the wiring...

Hey everyone. I have a bit of a tricky problem that I'm hoping is just some small oversight on my part. I've got the 2.4 L DHC 97 Stratus. I just finished a head gasket job and now I'm getting a crank, no start condition. I noticed I was getting no fuel pressure at the rail and when checking...