DodgeTalk Forum banner

Search results

1-20 of 493 Results
Advanced Search
  1. Who has a 05 2500 manual trans?

    3G Dodge RAM - General Talk
    Thanks again, I went back with my laptop and got the VIN. I'll give the dealer a shot again Monday. Good catch...
  2. Who has a 05 2500 manual trans?

    3G Dodge RAM - General Talk
    That's a thought, maybe I can find one locally I can o look at. I was a little surprised today when my previous goto folks came up empty. lol Thanks,
  3. Detroit truetrac questions

    3G Dodge RAM - General Talk
    I've had the DTT for about 5 years and lean on it fairly often with no issues.
  4. Who has a 05 2500 manual trans?

    3G Dodge RAM - General Talk
    Gentlemen, I need anyone with a 05 Ram 2500 manual trans with a hemi to take a look at their PCM and post or PM me the number from it. It should be something like 56028 967AB. My local dealer has not been able to help and all the places I've tried to order from want me to provide the number off...
  5. Cam & crank Position sensors

    3G Dodge Ram Performance Talk
    The P0016 is a sensor or wire related problem. The Crank and cam sensor share the same ground wire. Both are somewhat close to the exhaust and if they weren't put back on the harness standoff's they might of been damaged. The cam sensor is tricky to unplug. The sensor is located in a recess on...
  6. 03 to 05 swap - Idling issues and diablo failure

    3G Dodge Ram Performance Talk
    Diablo's are very sensitive to voltage change. What's the condition of your battery? I would at least charge it over night. VIN numbers are mostly to identify the accessory package the vehicle has. I used a salvage yard PCM for a couple of years with the wrong VIN in it. I now have a Ram 1500...
  7. 03 5.7 v8 Engine shot (so the shop says) need suggestions...

    3G Dodge RAM - General Talk
    Al, It's been stated over the years that the 6.1 push rod could cure some hemi tic by seating deeper into the lifter. I personally have not used 6.1 push rods on a stock cam. So I guess the question is, what is the length difference between the two? To answer that without going out and measuring...
  8. 03 5.7 v8 Engine shot (so the shop says) need suggestions...

    3G Dodge RAM - General Talk
    You might consider Moe's, summit, Jegs or Rock Auto.
  9. 03 5.7 v8 Engine shot (so the shop says) need suggestions...

    3G Dodge RAM - General Talk
    I've had my 03 since new and I never heard of that particular repair kit. The pieces had to be bought separately. You need only springs, but I would look at the push rods and change the seals. I have spare springs (used) and both 5.7 and 6.1 push rods (used). I might even have a set of new...
  10. 03 to 05 swap - Idling issues and diablo failure

    3G Dodge Ram Performance Talk
    I would call that a long enough test to determine how well they work. I'm sure over that period of time you have read threads where others haven't been as fortunate.
  11. 03 5.7 v8 Engine shot (so the shop says) need suggestions...

    3G Dodge RAM - General Talk
    The 6.1 exhaust valves (16) use to cost around $70. You can re-use the keepers and retainers. The truck would be basically undriveable without the front O2 sensor installed. The valve springs can be installed with the heads in place. Try the dealer for the springs. I have a set of used 6.1...
  12. Stiffer Front Shocks

    3G Dodge RAM - Sport Truck Talk
    If your shocks are good condition then the Timbren bumps is your answer. Been there, with these you can not bottom out, you will have to learn in your own way..
  13. Stiffer Front Shocks

    3G Dodge RAM - Sport Truck Talk
    This is a common problem with a easy solution. You are expecting too much from the shock with limited travel. The front bump set close to the lower control arm. I used Timbren rubber springs rated at 990# each with a shim under it to keep the tires from rubbing the inner fender liner. Remove the...
  14. LT's and fuel line clearance

    3G Dodge Ram Performance Talk
    Auto parts store has heat insulation available. I wrapped the starter and anything close to the headers.
  15. Plug Wire Question??

    3G Dodge Ram Performance Talk
    I would use the Dorman's over using Taylors. Taylors have been reported as hard starting and misfires.
  16. 03 to 05 swap - Idling issues and diablo failure

    3G Dodge Ram Performance Talk
    Ahhh tuning the much beloved 03..... I've been chasing the tail for a long while myself. I would recommend either installing the 6.1 dual coils or at least removing the shorties, they have proven themselves to be problems at times. Simple enough to change plugs. Are you getting any codes? If not...
  17. EVAP codes keep comming on (UPDATED 7-2-2015)

    3G Dodge RAM - General Talk
    As stated a gas cap is usually the fix. You can test the cap using vasoline or grease on the rubber seal to see if that fixes the problem. The hoses on the NVLP uses plastic clamps. You can replace them with clamps. Changing the tank for this problem will not fix the problem unless it has a hole...
  18. 03 5.7 v8 Engine shot (so the shop says) need suggestions...

    3G Dodge RAM - General Talk
    Valve springs have been a issue on some 03/04's. The basic fix is to replace all the springs with 6.1 exhaust springs. If the push rods are worn the replacing them is needed. I you have the hemi-tic then you might consider using 6.1 push rods. Good luck..
  19. Just bought a 89' D250 12v

    Dodge Ram Truck 1st Gen (88 - 93) Forum
    It's a D250, two wheel drive.
  20. Just bought a 89' D250 12v

    Dodge Ram Truck 1st Gen (88 - 93) Forum
    Just picked this truck up. Only major problem so far is the passenger side upper ball joint is trashed and had been welded in place. This in turn damaged the knuckle. So waiting for parts to come in and should have the new UCA, upper ball joint, lower ball joint and knuckle installed next week...
1-20 of 493 Results
Top