Have these torsion bars being cranked? - DodgeTalk : Dodge Car Forums, Dodge Truck Forums and Ram Forums
 
Thread Tools
#1 Old 06-10-2006, 02:41 AM
jaysrippen
Registered User
 
Join Date: Jul 2004
Location: Canada
Posts: 45
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
(Thread Starter)
Have these torsion bars being cranked?

Hey, what is the stock torsion setting, I guess, how do I know how much these have being cranked from stock (aprox). Measurement from wheel centre to top of fender of a stock would work for me. Thnaaks

Great site, good info, good guys!

LOVE anything motorized!!!
6 motorbikes (4dirt, 2street)
2004mxz Renagade 800 (big sled head)
Hot rod/musle car intrests
2000 concorde LXI (wifes ride)
Past rides:
96 Dodge ram15004x4
95trans-am 5.7/6spd
91 Celica turbo/allwheel
jaysrippen is offline  
Sponsored Links
Advertisement
 
#2 Old 06-10-2006, 08:13 AM
snobnk
over 100,000
 
snobnk's Avatar
 
Join Date: Apr 2005
Location: south of boston
Posts: 382
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
37 3/8 from ground to fender

2005 1500 4x4 quad cab-
20's
Hemi
oem 4"oval nerf bars
sirius radio
power,heated tow mirrors
led's in cubby and int lights
access lorado tonneau
viper 1 mile starter
12 v outlet in bed
3 turns on t.b.
silverstars
power wire
hellas in the grill
Ride rite air bags
275-65-20 ATS wranglers
bilsteins
magnaflo
----------------------------------------------------
WHITE TRUCK CLUB MEMBER #43
snobnk is offline  
#3 Old 06-10-2006, 10:19 AM
jerhemi
Registered User
 
jerhemi's Avatar
 
Join Date: Oct 2005
Location: Toronto,Canada
Posts: 1,199
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
to my understanding, there is no firm stock torsion setting.. it all depends on how they were set at the factory.. just measure the rear from the ground (or center of the rim) to the feneder cut out and do the same for the front....

2004 DODGE RAM Q/C HEMI CNG/GASOLINE
jerhemi is offline  
#4 Old 06-10-2006, 05:26 PM
Island Ram
Registered User
 
Join Date: Apr 2006
Location: Kauai, HI
Posts: 75
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Should be close to 2 inches difference from front to rear.
Island Ram is offline  
#5 Old 06-10-2006, 10:52 PM
bucci
Registered User
 
bucci's Avatar
 
Join Date: Jan 2005
Location: Jessup, PA
Posts: 1,028
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Ride height for Ram 1500 4x4: To be performed with vehicle supporting it's own weight & taken on both sides.

1. Measure height from ground line at the centerline of the rear lower control arm bolt front tip.

2. Measure the height from the ground line at the front spindle centerline (Static load radius).

3. Subtract the first measurement from the second measurement. The difference between the two measurements should be 58 mm (2.3 inches) +/-3mm (.12 inches).

4. If value is greater than max. (61 mm), tighten torsion bar.

5. If value is less than min. (55mm), loosen torsion bar.

6. Repeat previous steps until ride height is within specs.

Procedure is also listed in the service manual, Wheel Alignment 2-3.

2003 Ram 1500 4x4 RCLB 5.7l HEMI
Patriot Blue Pearl Coat
Laramie Package
bucci is offline  
Sponsored Links
Advertisement
 
Closed Thread

Quick Reply
Message:
Options

Register Now

In order to be able to use most of our features, you must first register.
Please enter your desired User Name, your Email Address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
The registration process requires you to activate your membership by following a link in an E-Mail that will be sent to you immediately upon completing this form. You must enter a valid email address or you will not receive this activation code and you will NOT be registered. Your E-Mail address is NOT publicly available to anyone as policy.

AOL E-MAIL USERS: Please click HERE for important info pertaining to your e-mail address.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.




Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
User Tag List

Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page


Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
315's with Cranked Torsion Bars enash 3G Dodge RAM - General Talk 2 03-03-2006 06:47 AM
Has anyone cranked up their torsion bars... lsigrandson Dodge Dakota 1st Gen (87 -96) Forum 10 12-03-2005 01:52 AM
Cranked up the torsion bars, check it out! acjrocks 3G Dodge RAM - 4X4 Talk 69 08-04-2005 03:48 PM
Got my torsion bars cranked Byron 3G Dodge RAM - 4X4 Talk 3 05-18-2005 09:07 AM
Torsion bars cranked NEW rack & ball joints mb190e 3G Dodge RAM - General Talk 1 11-18-2004 12:47 PM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome